Klein Tools
For use when light compact grip is desired and where conductor damage is not a factor. Swing latch to help hold cable in the jaw
Precision machined, mating surfaces and design dimensions, to extremely close tolerances. Ultra-durable "2000 Series" cutting knives for ACSR, bolts, nails, and most hardened wire. Pliers halves are matched side to side, jaw to jaw, and hot riveted. Drop forged, hardened, and tempered construction. Angled head design for easy work in confined spaces
Ultra-durable "2000 Series" cutting knives for ACSR, bolts, nails, and most hardened wire. Precision machined, mating surfaces and design dimensions, to extremely close tolerances. Smooth streamlined nose with knurled jaws. Pliers halves are matched side to side, jaw to jaw, and hot riveted. Drop forged, hardened, and tempered construction. Cutting knives meet at the hinge first and meet at least 1/2 of the knife length. Special groove at hinge for gripping and pulling flat fish tapes...
General-purpose selection of the most frequently used nut drivers
Heat-treated and tempered-steel blades with clamshell package. Set is provided in reclosable seal-tight vinyl pouch. All with cushion-grip high quality
Two wire cuttersâ??one at tip the other halfway back near stripping holesâ??double the utility of this tool. Crimps 7-8 mm insulated and non-insulated terminals lugs and splices
Riveted to assure long life. Holder for Klein bull pins. Holds all standard bull pins
Heat treated precision ground shear action curved cutting blades. Plastic coated high leverage handles. Made in U.S.A
Soft handle material on outer surface for comfort and a firm grip and hard black material on inner surface and handle ends for toughness and durability. For insulated and non-insulated terminals and connectors. Wire cutter in nose
Soft handle material on outer surface for comfort and a firm grip. Hard black material on inner surface and handle ends for toughness and durability. Cuts ACSR screws nails and most hardened wire. High-leverage
No. 4 canvas. Heat-resistant hard-leather bottom. Web loop for sliding over a belt. Height in front is 12" height in back is 15-1/2" diameter is 2-1/2"
Have tool-slots for two erection wrenches. Tunnel loop is riveted to assure long life. Holds erection wrenches and adjustable head construction wrench Cat. No. 3239
Induction hardened cutting knives for long life. Heavier design for greater cutting power. Extended handles provide added reach and leverage. Cleanly strips 12 AWG wire
Handle resists slippage. Handle resists oil gas and water. Heat-treated and tempered shank. Narrow tip permits blade access where space is limited
Handle resists slippage. Handle resists oil gas and water. Heat-treated and tempered shank. Square shank for wrench assisted turning
Cuts up to 4/0 aluminum and 2/0 soft copper 100-pair and up to 24-gauge communication cable. Shear-type jaws
Precision machined, mating surfaces and design dimensions, to extremely close tolerances. Ultra-durable "2000 Series" cutting knives for ACSR, bolts, nails, and most hardened wire. Pliers halves are matched side to side, jaw to jaw, and hot riveted. Drop forged, hardened, and tempered construction
Hex head drives nut and socket screws. Handle-end color-coded for size identification
Individually tested to exceed standards. Tips are precision ground to fit screw openings securely and resist slippage. Cushion-Grip handles for greater torque and comfort. Patented Tip-Ident® quickly identifies the type of screwdriver and tip orientation. Two layers of insulation provide protection against electrical shock
Deep ribbed design. Heat-treated and tempered shank. Handle resists slippage. Accurate fit and more torque without slippage. Handle resists oil gas and water. Profilated tip for a more consistent geometric symmetry
Twists and cuts soft annealed rebar tie wire. Rivet is closer to the cutting edge for 46% greater cutting and gripping power than other plier designs. Spring loaded action for self-opening
Twists and cuts soft annealed rebar tie wire. Spring loaded action for self-opening
Precision shear-type blades for clean cuts on solid and stranded copper wire. Easy to read markings on both sides
8" x 8" inside pocket. Polypropylene rope handle reinforced with leather at splice around top ring. No.1 canvas with Cycolac top ring and molded bottom. Leather coated bottom extends 3" around sides
Crimps insulated and non-insulated terminals and 7 to 8 mm ignition terminals. Narrow serrated plier nose to pull loop and bend wire
Lightweight. Shears wire up to 14 AWG with flush-cutting action. Compact head. Steel hold-open spring
Cuts bolts clean. Cuts strips and gauges wire. Measures stud sizes crimps insulated terminals
Drop-forged. High-leverage. Extra-heavy-duty head area gives maximum strength and durability. Handle features an extra-deep offset. Allows use on a range of bolt-hole sizes without binding
Ruler Screwdriver & Wrench Holders No exposed rivets in back. Riveted to assure long life. Nickel plated alloy snap. Pockets for 7" 8" and 9" side-cutting pliers most screwdrivers 6' folding rules and open end wrenches from 9/16" to 13/16"
Handle resists oil gas and water. Profilated tip for a more consistent geometric symmetry. Heat-treated and tempered shank. Accurate fit and more torque without slippage. Handle resists slippage
Drop forged quick-release buckle. Mildew-resistant blend of cotton/polyester. Worn over users clothes and harness. For emergency situation where the wearer has to quickly disengage the belt
Unique ratchet-action holds cable tight. 1-hand operation. Large plastic covered non-slip grip finger-formed handles. Allows rapid straight cuts with minimum effort. Hold-open spring speeds cutting action. Quick-release lever opens blade at any time. Cuts copper aluminum and multi-conductor cables
Handle resists slippage. Handle resists oil gas and water. Heat-treated and tempered shank. Narrow tip permits blade access where space is limited
Heat-treated and tempered shank. Handle resists slippage. Handle resists oil gas and water. Deep ribbed design. For electrical telephone and work in recessed holes and other tight space
Designed for tools with hang holes. Riveted to assure long life. Loop with snap hook for carrying an adjustable wrench welderâ??s igniter or other tool with hang hole
Tapered nose for easy working in confined areas. Easy working in confined areas
Slim head design for working in confined areas. Hot-riveted joint ensures smooth action and no handle wobble. Induction hardened long-lasting cutting knives. Knurled jaws for sure wrapping and looping. Curved handles provide greater tool control
Riveted to assure long life. Cut-out sides for easy access to tape. Holds medium-sized power return rules
Smooth aluminum alloy with wear parts made of steel. Easily removable cover plate rewind knob
No.6 canvas with Cycolac top ring and molded bottom. Polypropylene rope handle reinforced with leather at splice around top ring
Precision holes for wire stripping. Lean plier nose pulls and loops wire. Scissor-type blades are precision ground and heat treated to hold their edge. Highly visible AWG and mm wire gauge sizes painted and embossed in the metal
