Flange Wizard®
The Magnetic Tape Holder has been designed with no removable parts and works with most industrial measuring tapes. It is a great little magnetic pocket level and a third hand when doing difficult measuring jobs while working alone. Secure the end of your tape while laying out close tolerance measurements from the end or the center of your material. This tool is machined from aluminum and anodized for a protective finish. A strong 25 pound pull magnet set in epoxy secures the tape holder to your...
Both tools are machined from quality aluminum material then anodized for lasting protection. They have a one piece “Y” shaped body design with a 2-1/2° increment degree dial that turns 360°’s. The degree dial has a built-in dial for leveling the tool at various angles. The hardened center punch marks your set position by taping with a hammer (vial and center punch are replaceable for lasting service). Magnets in the legs will free up the users hands for a safer and more accurate layout mark....
The Circle Wiz Cutting Attachment is a must for anyone who cuts small to medium holes in plate or pipe. It is especially handy for cutting out the holes for matching saddle cuts, weldolets and threadolets. Made of finished high quality steel. The universal bushing will adapt to any size or make of conventional cutting torch. Will cut holes from 5/8” to 8” in diameter (recommend Chariot Cutting Guide P/N 24219 for larger holes). Simply slide the center pin along the hex arm to attain the proper...
The degree level is a shirt pocket size (1-1/2” x 2-3/8” x 5/8” thick) degree dial level that makes it easy to establish angles, set tanks, layout keyways and measure decline or slope. The level body is permanently marked in 2.5° increments and numbered every 10 degrees. It has strong magnets in the base for easy hands-off use and can even hold the end of a tape measure for solo use. Great level for getting angles on hard to reach pipe or structural steel details. Tool is machined from aluminum...
The Magnetic Circle Layout & Burning Guide is a circle layout tool with sliding soapstone holder and 360° scale on the magnetic base. It will cut circles up to 30” in diameter. Bolt circles, hole locations, baffle plate placement, and circle sectioning for any number of reasons is a snap with Flange Wizard®’s layout scale and sliding soapstone holder. As a circle burning guide, use this same tool to cut a round plate; simply place the sharpened pin of the layout tool into your center punch...
The Magnetic Torch Guide is a 24” stainless steel straight edge rail that comes with two (2) strong, heat resistant, adjustable, magnetic blocks that can be positioned to accommodate any cutting job. The 24? Extension #23040-24 comes complete with one (1) magnetic connecting block and a 24? cutting rail. The connecting blocks are slotted on three (3) sides giving them the capability to fasten to your cutting rail in whatever position your job requires The ON/OFF switch makes setting up easy and...
For 8? to 48? pipe and 48? structural beams. Structural beam layouts and marking angles or saddles on pipe and tubing are a snap with the Master Marker. Replace multiple templates with just one tool. The Master Marker comes with a unique design that allows you to telescope out over existing welds to layout angles or change the angles of pipe fittings to meet your special needs. Redesigned marking arm is completely separate from the main body. It has its own 360° rotating shaft with a built-in...
The Chariot Cutting Guide is a must for every tradesmen who uses a conventional cutting torch. The Chariot Cutting Guide will cut circles up to 39? in diameter. It can cut holes as small as 5/8? when used without the axles. It can bevel circles up to 36? in diameter. Cut straight, irregular shapes, circles and bevel with this versatile tool. Plated steel construction at heat stress points. Universal bushing fits all conventional torches. 15-1/2” extension (p/n 3311-EX) is available for larger...
All models of the Pipe Aligner will two-hole (make 2 holes of the flange horizontally level with the ground) and vertically level the face of the flange in ONE easy step. Threaded models have fast release double lead threads. All models have one pin that has a 360° vial for easier vertical leveling that just “snaps” in and out for easy replacement. The Pipe Flange Aligner saves valuable fit-up time, in most cases it cuts fit-up time in half and eliminates the frustration of balancing a level on...
A person who works with pipe needs the finest tools available and a way to protect them when not in use. The four (4) quality tools in this case are a must when working with pipe. Case #8900 (15?L x 10?W x 3-1/2? Deep) includes: 1 – Pipe Flange Aligner # 38240-T, 1 – Standard Magnetic Centering Head # 53076-M, 1 – Pocket Pro Level # PP-200, 1 – Small Wizard Pipe Wrap # WW-16, 1 – Flange Wizard Catalog, 1 – FREE BONUS Vial Repair Kit # 5102